• Single boiler with PID Controller
• Available in Red, Yellow, Blue and Black
• Fast Heat-Up mode: Heating phase 5-7 min
• Brewing counter in seconds
• Programmable ECO mode
• Programmable temperature mode
• Brass boiler – 0,4 l
• Boiler insulation
• Copper heating
• Water tank with 2,8 l volume
• Removable water tank lid
• Vibration pump
• Pump pressure gauge
• Expansion valve for brewing pressure adjustment
• Button panel
• Rotary valve for steam extraction
• Cup tray
• Max. Power usage EU, UK, CH, AU: 230 V/1300 W
• Weight 12.9 kg

Dimension (mm):
• 210W x 362D x 381H without portafilter
• 210W x 410D x 381H with filter holder

• Heat exchanger system
• Profitec brew group with stainless steel mushroom
• 3 PID controlled boiler temperatures selectable
• Preinfusion ON/OFF
• ECO mode ON/OFF
• Adjustable expansion valve
• Dual gauge for boiler and pump pressure
• 1.6 l stainless steel boiler
• Stainless steel heating element
• Boiler insulation
• Vibration pump
• 2.8 l water tank with built-in adapter
• Automatic low water volume shut-off
• Low-wear rotary valves
• High-quality steam and hot water wands
• Removable cup tray
• Bracket for the blind filter underneath drip tray
• Different colored valve disc lets included

Power usage:
• EU, UK, CH, AU: 230V/1400 W
• US: 115 V/1400 W
• Weight 21.5 kg

Dimensions (mm):
• 228W x 448D x 372H without portafilter
• 228W x 558D x 372H with portafilter

Technical Data:
• Dipper (one-circuit) system
• Heavy duty lever brew group (7.8 kg)
• Handles of the hand lever, lever valves and portafilters handcrafted American walnut
• Practical lever valves for steam and hot water extraction
• Large, pine green boiler pressure gauge
• PID control for regulating the boiler temperature
• Programmable ECO-Mode
• Switchable from water tank to a fixed water connection
• Connection to a water drainage is possible
• The vibration pump is only activated when using the water tank
• The vibration pump is not activated when using a fixed water connection
• 3.5 l copper boiler
• 2.8 l water tank with built-in adapter
• Drip tray with about a 1.25 l capacity
• High quality steam and hot water pipes
• A large removable cup tray
• Power usage: 230V/1600 W
• Weight: 35.5kg

Dimensions (mm):
• 339W x 505D x 492H without portafilter
• 339W x 593D x 740H with portafilter and lever up

Fits Standard on Profitec / Rocket / ECM / E61 groupheads

• Lightly fill the portafilter basket to the top
• Use your finger to gently even out the grounds
• Lightly press the tamper into the grounds and find a good center point
• Evenly apply approximately 30 lbs of pressure to the grounds
• Tap the side of the portafilter to reveal loose grounds
• Lightly tamp these loose grounds into place
• Sit back and enjoy one of the coolest looking effects in espresso extraction

1. Unscrew the mushroom with an open-end wrench sized 36mm across flats,
2. Caution: Be careful to avoid scratches!
3. Screw the new profiling valve P1025 in, at the position of the Mushroom.
4. Unscrew the screw with a 5mm hex key.
5. Mount the pressure gauge P1026 where the hex key screw was inserted.
6. The Teflon seal of the screw has to be reused.
7. It is recommended to use FDA-approved thread sealing too,
8. Caution: Do not fasten the gauge to right, to avoid damaging to the thread.
9. Close the valve by rotating the bolt clockwise completely.
10. Place the bushing to point in desired direction for closed position onto spindle.
11. Screw the ball grip in and tighten it.
12. Unscrew the purebred-cylinder at lower brew group with an open-end wrench sized 36mm
13. Exchange the spring to the supplied P1029-spring
14. Insert the valve spindle in the purebred-cylinder,
15. And reassemble it to the lower brew group.
16. Unplug your machine from power supply before assembling the Profitec E61 Flow Valve

Spare Parts – E61 Steam Nozzle 4 Holes

Spare Parts – Gasket Valve Spindle

PROFITEC-SPARE PARTS WASHER AXIS GROUP E61